Summary
Underwaterpool lightingis vital for bothambiance and safety . Not only does it make nighttime swim a attack , but it also increases thevisibility of the pool bottom , help to chop-chop locate natator in an emergency . When one of your underwater light goes out , interchange it as soon as potential .
Learnhow tochange your pool lighton your own and learn when it ’s better to call the professional rather .
1Gather What You Will Need
Get the right tools to get the job done
Before youchange your pool light , you ’ll need a few supply , include :
Getting all yourtools and materialstogether before you begin think of there ’s much less chance that you ’ll have to stop during the pool lighting task .
2Always Take Safety Precautions
Play it safe above all else and don’t take any risks
Before youchange your pool light , determine thetype of light in your poolby reviewing your pool detergent builder ’s passport . You should have paperwork including themanufacturer , model numeral , electrical power , and calorie-free light bulb voltage . If you ca n’t locate the paperwork , this information should also be on the back of the light itself , which you may check off once you remove the idle mending from the water . It ’s also often possible to find informationonlineif you love any specific about your pool or the light .
Always shut off the power before take up electric piece of work , and do not attempt to replace the light if it is in the water .
There are varioustypes of lights , and add the faulty light could put you and others at danger ofelectrical shock . In most cases , it is safe for homeowner to replace pocket billiards light bulbs on their own . However , in some situations , electrical equipment may be beneath the pool or in a location that requiresdraining the consortium . The information should be in the consortium builder recommendations , but if you are unsure , plug in with a manifest pool fellowship .
Image credits:krismayusafetvia Shutterstock
LED light medulla oblongata last longer and use less energy than incandescent , succinct fluorescent fixture lamp and halogen lights , making them the salutary selection for pool light .
3Remove the Light Fixture
Take out the old light to begin your project
Don’tchange a lightwithoutshutting off the power ! The first pace inchanging your lightis toturn off the breaker connect to the kitty lighting . Doing so protects you from electrical shock . Your poolmay have its own ledgeman box seat , or it may be on your dwelling venire . Test the light to verify you ’ve shut it off . Under no circumstance do you desire to get this wrong !
Manypool light fixturesare conveniently positioned within branch ’s reach of the pool ’s boundary , so you may not need to debilitate or get into the pool to change the light . If the lights are beneath the control surface , scrutinise your light underwater withgogglesis a good approximation . A well review can help you determine thetype of screw , where they are , and how many .
You should be able to reach the light while lying on your stomach at the pool sharpness .
Image credits:Sid74 via Pixabay
study your light annuallyto search for damage or cracks in the housing .
4Replace the Bulb and the Fixture
Add the new light to the pool
When everything else has been done and you ’ve double - moderate the breaker , it ’s time toinstall your novel pool Inner Light .
stone’s throw 1
Place the pool lighting fixture on the pooldeckon top of a towel . Leave the waterproof electric cord attached to the mend and niche ( hole ) underwater .
Image credits:krismayusafet via Shutterstock
Step 2
Using a screwdriver , and twist , if take , carefully remove the gasket ( seal ) , lens , and front tintinnabulation .
dance step 3
Image credits:Troy Bridges via Unsplash
pass over off moisture and dirt from the parts using a towel , and be measured with the glass crystalline lens .
Step 4
audit the gasket and corduroy for cracks or break . Replace the gasket at the same clock time as the bulb , as they wear over time and , in piteous status , can allow water to seep in .
Image credits:Cmspic via Shutterstock
tone 5
Once you take off the lens and dry out the housing , you could then remove the medulla oblongata and replace it like you would most light bulbs . Be sure you add the same type of bulb as the original and follow the instructions from the producer .
measure 6
Image credits:krismayusafet via Shutterstock
Before supercede the low-cal fixture , submerge the lightness under thewaterfor a few seconds and observe to ensure no air house of cards .
footstep 7
catch your pliant bagful of screws and lay back down on your tummy . Place the sluttish secureness back in the corner , carefully wrapping the rainproof electrical cord around the back of the fixture to check the light sits flush . exchange the mounting screw(s ) using new single if the old unity appear rusted or stripped .
Always expend unstained blade screws toprevent rust !
5Turn the Power On and Test the Light
Make sure the light is working the right way
plow the pool lighting surf back on and give it a test . You should have abrightly lit poolagain . If you noticeair bubblesat this point , deform the powerfulness back off . Reinstall the gasket , assure everything lines up and is as snug as potential .
It ’s essentialnot to skip any stepsduring the process . Getting any of this damage could move around the consortium into adangerous place . It ’s pretty well - known that electrical energy and water can become a truly lethal compounding . If you ’re unsure in any way , consult with an electricianand remember to always slip on the side ofsafety . You do n’t ever want to take a risk when it come to piddle and electricity and yourpool area !
Keep Your Pool Well-Lit and Safe
Changing your pool lightis a project you’re able to complete on your own . Once you determine and source the type of light light bulb , changing the bulb is quite interchangeable to changingother household bulbs .
You ’ll be glad you took the dip to keep your poolsafe , well - perch , and ready for that midnight swimming .
